Gig Posters

Posters: 158784 | Bands: 137791 | Designers: 11679                 
   
       RSS Feeds

Username:   Password: 
Register      

Social Networking Activity                 



 Bands  Designers  New Arrivals  Top Lists  Forums  Buy Posters  Submit  Merch Store  Advertise  Widgets  Help

Search:

Type: Posts; User: squeegeethree; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    14
    Views
    509

    Yes I can see that. I just think there's a...

    Yes I can see that. I just think there's a distinction between dyes and pigments. We use a lot of pigment with TW inks and they mix in very well. Pigments do not mix well in other brands of inks...
  2. Replies
    14
    Views
    509

    I'm not sure that TW's pigment are acid-dyes. ...

    I'm not sure that TW's pigment are acid-dyes. What makes you think they are? We use their concentrates (which are pigments) and dry artist pigment all the time.
  3. Replies
    3
    Views
    154

    7000 series is just a smaller version tan the...

    7000 series is just a smaller version tan the 9000 series. There's no real difference beside the width.
    The real question is which model of the 7000 series. Anything older than a 7600 I would not...
  4. Thought so. Glad you figured it out.

    Thought so. Glad you figured it out.
  5. Replies
    4
    Views
    160

    print a flat of base on the other side to reverse...

    print a flat of base on the other side to reverse the curl.
  6. That's funny I have a band named The Rebell!ous...

    That's funny I have a band named The Rebell!ous Sp!r!t.
  7. You can try ammonia. You can also try using the...

    You can try ammonia. You can also try using the inks itself, but yes there is a cleaner made special for vinyl inks.
    But really, unless you have good ventilation and you use properly rated...
  8. Vinyl, Latex and Acrylic are all different...

    Vinyl, Latex and Acrylic are all different things. I've only encountered a true latex ink once and it cleaned up with ammonia. Vinyl inks clean up with their own solvent. Acrylic inks clean up...
  9. Inks that are too thin can do this as well. As...

    Inks that are too thin can do this as well. As well as substrates that aren't absorbent.

    If you look at the bottom of the screen right after you print but before you flood you may see lots of ink...
  10. Replies
    14
    Views
    509

    Nice post Haven. I will add that all WB...

    Nice post Haven. I will add that all WB acryllics are Urethane base so your insight will apply to everyone's wb inks. The only other base besides urethane is epoxy and I've never seen that in a WB...
  11. Replies
    16
    Views
    684

    When the squeegee "flops" over your pressure or...

    When the squeegee "flops" over your pressure or angle is so great that the flat side of the blade instead of the edge is running over your stencil.
  12. Replies
    16
    Views
    684

    There's no real need for the dish soap IMO. The...

    There's no real need for the dish soap IMO. The emulsion is extremely hungry for water. By wetting the screen before you begin the emulsion sucks up that water instead of the water in your ink. If...
  13. Replies
    16
    Views
    684

    It looks like your ink is drying in your screen. ...

    It looks like your ink is drying in your screen. Wet your screen completely with water before you put any ink on the screen. Print off the watery ink on waste sheets and try to be fast about your...
  14. Replies
    14
    Views
    509

    It's just a fact of life when printing with black...

    It's just a fact of life when printing with black and red. We use Fantastic instead of 409 and it does help to a degree.
  15. Replies
    14
    Views
    509

    Ghost images should not effect your printing...

    Ghost images should not effect your printing unless it's actually died in ink. So you either have to get over it if they are printing fine or use dehazer which is nasty
  16. Replies
    10
    Views
    951

    haha. Having paper towels that are drying behind...

    haha. Having paper towels that are drying behind box fans getting sucked in to them and shredded, blowing paper towel bits into freshly reclaimed screens is also helpful
  17. Replies
    10
    Views
    951

    Here I think the OP was blowing shards of rust...

    Here I think the OP was blowing shards of rust and dirt into his mesh drying with that compressor. I would never use a compressor to dry a screen unless it had a huge and properly maintained...
  18. Replies
    3
    Views
    257

    Reset your printer by finding the hidden 5 button...

    Reset your printer by finding the hidden 5 button combo online somewhere. Double check that all wires are properly connected. If your printer is more than 10 feet from your computer and you are...
  19. Replies
    3
    Views
    295

    This should be the standard imo

    This should be the standard imo
  20. Geez this thread bringing out a lot of the...

    Geez this thread bringing out a lot of the old-timers.
  21. Replies
    2
    Views
    297

    Personally I think you would be fine putting your...

    Personally I think you would be fine putting your collection on the web. Others do it all the time.
  22. Replies
    13
    Views
    646

    Nice thing about making prints is you can have...

    Nice thing about making prints is you can have both.
  23. Replies
    5
    Views
    300

    UV glass is rather expensive I seriously doubt...

    UV glass is rather expensive I seriously doubt they would have bothered when making the table.
  24. Replies
    13
    Views
    646

    Well speaking as a person others outsource to,...

    Well speaking as a person others outsource to, print quality is one thing. No you will never be able to match our print quality because that's what we devote ourselves to do and charge accordingly. ...
  25. never seen a 3" inch core on film. I stand...

    never seen a 3" inch core on film. I stand corrected. regardless we use 2" core and fixed all our problems with the custom paper profile and feed adjustment
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4